Error Code tajima machine

"TROUBLE SHOOTING ''

error machine

error code	cause	Abatement
211	Stop position does not fit the red line	Check the main shaft of motor / encoder / belt motors Slide into position 100 '
212	The position of the needle being dropped	Put on a posii to correct / position 100 '
221	The position of the frame to the right over the edge	Movement back towards the left frame do not pass the limit
222	The position of the frame to the left over the limit	Movement back towards the right frame do not pass the limit
223	Position the frame up over the limit	Movement back frame downwardly do not pass the limit
224	Position the frame down over the limit	Back frame upward movement do not pass the limit
225	Position frame + x-axis (right) passes the limit (for machine cap)	Movement of the frame to the right place
251	Lubricating oil in the tank runs out	Refill the oil in the tank
281	Time replace needle / color over 15detik	Adjust the needle position manual / rotating motor
291	Yarn breaking / broken needle	Attach the yarn dang anti needle breakage
293	Yarn lifeboat end / consumables	Check or replace the lifeboat thread
2B1	Not biased read diskette or tape design	Check the data design (design order)
2B2	Not in accordance with the format machines	Check the data design (design order)
2B3	Data is not entirely legible	Check the data design (design order)
2B4	The function code in the design wrong	Check the data design (design order)
2B5	Sequins data is not normal	Check the data design (design order)
2B6	Serial I / F is not installed	Check the cable ssambungan in TFD
2B7	Data sets unfinished or incomplete	Perform a complete set of data
2B8	Error when reading data buffer	Check in setting reader TFD
2B9	Time entering data can not enter	Check the CPU card or card panel
2BA	Capacity memory exhausted	Remove one of the main designs that are not needed
2BB	Stitch in time the data is already depleted	Stop command repetition stitch
2BC	No. Design nothing in the machine's memory	Look up the correct design or re-record
2BE	In function of satin, boring, sequin yet in seting	Setinglah first if the puncture would be used
2C1	The time machine in star / stop panel is being used	Cancel pengoprasian first panel
2C2	One pengprasian setting panel	Fix pengoprasian setting panel
2C6	The machine is made the turn bobbin changer	Machines do not run on time change bobbins
2CB	Design images are too large over the limit tract	Adjust the machine capabilities (Width tract)
2E3	Electricity is off when the engine is running (Including the use of emergencystop)	Use pasilitas power resumes to return to the correct position
311	Encoder does not respond + member 5detik Or belt motors dynamo defective / fox	Check rotary encoder, check belt Dynamo or main shaft drivers
312	Signal of encoder z no	Check if the encoder lines replace damaged
316	Dinamo is not the way	Check the motor belt
321	The frame can not move	Check or replace the driver unit
322	Frame x-axis is not the way	Check or replace the driver unit
323	Frame y-axis is not the way	Check or replace the driver unit
331	Bobbin charger is not normal	Check / setting bobbin section Canger
352	Sequins function is not normal	Check or replace the card Sequins
382	Color change is not moving	Check the needle position sensor or replace the motor color change
383	Signal to turn the color does not exist	Check the potentiometer (position sensor needle)
384	Replace the sensor signal no color	Check the photo-interrupter
3A1	Movers no thread cut signal	Priksa join or replace the card
3A6	The position is not correct thread cutter	Check the position sensor thread cutter / movable knife
3A8	Tread driver holding no signal	Check head card
3B5	Signal panel between CPU card and card, CPU card And inverter, or between CPU card, card join, and no head card	Turn off the engine and check the cable connection Among these card_card
3D1	Volt battery is weak	Turn on the machine and then setting the parameters and input designs
3D3	Power supply is not normal	Check the cable connection or replace transformers
3D4	Data check sum is not detected	Change CPU cardnya
3D5	A ram check sum data is not normal	Reinstall the program if there are any engine system or fix the panel cardnya
B01	Time to enter any type floppy format	Reformat to type the correct capacity
B02	Record diskette of the machine can not enter	Try again if you keep guns could try to replace the use of other diskettes
B03	Protect the diskette active	Go to protect diketnya
B04	Floppy was not installed in fdd	Put a floppy
BC1	The data unreadable floppy	Replace with another designnya
BC2	Time recording design to an existing machine the same	Rename designnya
BC4	Design that is recorded to a diskette no	re-record
BC5	The capacity of a floppy disk is full	Wear new diskette
C01	Problem about FDD	Check the cord is damaged or if Fddnya replace with new.

============================

"TROUBLE SHOOTING''

Error mesin

Code eror	Penyebabnya	Penanggulangannya
211	Stop posisi tidak pas garis merah	Periksa main shaft motor/encoder/belt motor Geserkan ke posisi 100’
212	Posisi jarum sedang turun	Putarkan ke posii yang benar /posisi 100’
221	Posisi frame ke kanan melewati batas	Gerakan kembali frame kearah kiri  jangan melewati batasnya
222	Posisi frame ke kiri melewati batas	Gerakan kembali frame kearah kanan  jangan melewati batasnya
223	Posisi frame ke atas melewati batas	Gerakan kembali frame kearah bawah  jangan melewati batasnya
224	Posisi frame ke bawah melewati batas	Gerakan kembali frame kearah atas  jangan melewati batasnya
225	Posisi frame sumbu +x (kanan) melewati batasnya (untuk mesin topi)	Gerakan frame ke tempat yang benar
251	Minyak pelumas di tank habis	Isi kembali oli di tank
281	Waktu ganti jarum / warna lebih dari 15detik	Atur posisi jarum manual /memutarkan motor penggerak
291	Benang putus / jarum patah	Pasang benangnya dang anti jarum yang patahnya
293	Benang sekoci putus / habis	Periksa benang sekoci atau ganti
2B1	Tidak bias baca disket  atau pita design	Periksa data design (design rusak)
2B2	Tidak sesuai dengan format mesin	Periksa data design (design rusak)
2B3	Data tidak terbaca seluruhnya	Periksa data design (design rusak)
2B4	Fungsi code pada design salah	Periksa data design (design rusak)
2B5	Data sequin tidak normal	Periksa data design (design rusak)
2B6	Serial I/F belum terpasang	Periksa ssambungan kabel di TFD
2B7	Data set belum selesai atau belum lengkap	Lakukan data set yang lengkap
2B8	Eror pada waktu buffer pembacaan data	Periksa di setting reader TFD
2B9	Waktu memasukan data tidak bisa masuk	Periksa CPU card atau panel card
2BA	Capasitas memori habis	Hapus salahsatu designs yang sudah tidak perlukan
2BB	Waktu data stitch di ulang sudah habis	Hentikan perintah pengulangan stitch
2BC	No Design tidak ada di memori mesin	Cari no design yang benar atau rekam ulang
2BE	Pada fungsi satin,boring,sequin belum di seting	Setinglah dulu kalau pungsi tersebut mau di gunakan
2C1	Waktu mesin di star / stop  panel sedang digunakan	Batalkan pengoprasian panel terlebih dahulu
2C2	Salah pengprasian seting panel	Perbaiki pengoprasian seting panel
2C6	Mesin sedang melakukan pergantian bobbin changer	Mesin jangan di jalankan di waktu pergantian bobbin
2CB	Design gambar terlalu besar melewati batas bidangan	Sesuaikan dengan kemampuan mesin (lebarnya bidangan)
2E3	Listrik mati ketika mesin sedang berjalan (termasuk dengan penggunaan emergencystop)	Gunakan pasilitas power resume untuk mengembalikan ke posisi yang benar
311	Encoder tidak member respon +5detik Atau belt motor dynamo rusak/rubah	Periksa rotary encoder,periksa belt Dynamo atau main shaft drivernya
312	Signal dari encoder z tidak ada	Periksa jalur encodernya jika rusak ganti
316	Dinamo tidak jalan	Periksa belt motor
321	Frame tidak bisa bergerak	Periksa atau ganti driver unit
322	Frame x-axis tidak jalan	Periksa atau ganti driver unit
323	Frame y-axis tidak jalan	Periksa atau ganti driver unit
331	Bobbin charger tidak normal	Periksa/seting bagian bobbin canger
352	Fungsi sequin tidak normal	Periksa sequin card atau ganti
382	Color change tidak bergerak	Periksa Sensor posisi jarum atau ganti  motor color change
383	Signal untuk pergantian warna tidak ada	Periksa potensiometer(posisi sensor jarum)
384	Signal sensor ganti warna tidak ada	Periksa photo-interrupter
3A1	Penggerak potong benang tidak ada signal	Priksa atau ganti join card
3A6	Posisi pisau potong benang tidak benar	Periksa posisi sensor pemotong benang /movable knife
3A8	Tread holding driver tidak ada signal	Periksa head card
3B5	Signal antara CPU card dan panel card,CPU card Dan inverter, atau di antara CPU card, join card, dan head card tidak ada	Matikan mesin dan periksa sambungan kabel Di antara card_card tersebut
3D1	Volt battery lemah	Nyalakan mesin kemudian seting parameter dan masukan designs
3D3	Power supply tidak normal	Periksa sambungan kabel atau ganti transformer
3D4	Data check sum tidak terdeteksi	Ganti CPU cardnya
3D5	A ram data check sum tidak normal	Install ulang program system mesinnya kalau masih ada atau perbaiki panel cardnya
B01	Waktu  memasukan type format disket salah	Format ulang dengan type kapasitas yang benar
B02	Merekam disket dari mesin tidak bisa masuk	Coba lagi kalau tetap ngga bisa coba ganti pakai disket yang lainnya
B03	Protect disket  aktif	Buka protect diketnya
B04	Disket tidak di pasang di fdd	Masukan disketnya
BC1	Data disket tidak terbaca	Ganti dengan designnya yang lain
BC2	Waktu merekam design ke mesin sudah ada yang sama	Ganti nama designnya
BC4	Design yang di rekam ke disket tidak ada	Rekam ulang
BC5	Kapasitas disket sudah penuh	Pakai disket yang baru
C01	Fdd ada masalah	Periksa kabelnya atau kalau  Fddnya rusak ganti dengan yang baru.

Subscribe to receive free email updates: